How to Use Our Quick Shine® Deep Cleaner
Deep Cleaner to the rescue! Many of you have asked if there are any tips or tricks to the Deep Cleaner process so you can reapply the Quick Shine® Floor Finish to get your floors back to that WOW factor.
Today, we are happy to share with you the recommended steps below to give you confidence in conquering your floors like superman!
The Quick Shine® Deep Cleaner was specifically developed to not only deep clean but also to safely remove our finish from your floors. Quick Shine® Deep Cleaner/Wax Remover will also remove other waxes and finishes without harming hardwood floors or their polyurethane seal or any other type of hard floor surface. Below are 6 quick tips on how to use our Deep Cleaner:
- In a bucket, dilute the Deep Cleaner in HOT water as HOT water is more effective.
- Using a sponge mop or our Hardwood Floor Mop, apply it to the floor surface. Do small sections (5’x5’) of the floor at a time in order to maintain a more manageable removal and clean-up.
- Allow the Deep Cleaner solution to remain on the floor for a few minutes. CAUTION: Do not allow the solution to dry and re-adhere to the surface. If the solution appears to be drying, add a little warm water to keep the surface wet.
- The Quick Shine Floor Finish that you are removing should start to turn to a milky white film indicating the finish is being removed.
- After a few minutes, agitate with our microfiber scrubber pad. Aggressive agitation and elbow grease are typically required to remove ground-in dirt and multiple layers of the finish.
- Once you have removed the floor finish, rinse the area with clear, warm water and allow it to dry. Then you can proceed to the next 5’x5’ area and repeat steps 1-6.
NOTE: For heavy build-up, you may need to use a second treatment, and/or you can also increase the dilution from 1 cup per gallon to 2-3 cups per gallon. Deep Cleaner is concentrated, therefore it makes 3.5 gallons (at 1 cup per gallon), which should be enough for 500 square feet.
After completing this process, once your floors have completely dried you can now reapply a coat of our Quick Shine® Floor Finish or Quick Shine® Hardwood Floor Luster to bring your floors back to life giving them the shine they deserve!
We hope these simple steps have helped you with using the Deep Cleaner correctly and efficiently. Now you can proudly wear that S on your chest and have triumphed for your floors!
If you have further questions please do not hesitate to leave a comment below, email us, or call us at 1-800-255-1891. We are always here to help!
Can I use the hardwood luster with the hardwood shine that you offer? And if so, which one do you use first or how often should you use these products?
Hi Stephanie,
Yes, both products are compatible and can be applied over existing dry coats of one another. We recommend to start with Quick Shine Hardwood Floor Luster as it is fortified with Carnauba wax and will add durability. For application tips please contact customer service at 800-255-1891. We are always happy to help!
Can the quick shine be applied over acrylic floor finish?
Hi Judy,
Yes, Quick Shine is compatible to apply over acrylic based finishes.
Hi,
I used Quick Shine on my dark hardwood floors after having some work done in my house. I think there must have been some dust still on the surface, because now there are horrible streaks. Is it okay to use the deep cleaner on a floor that is stained, or will it also strip the stain? I need to fix this because it looks awful.
Hi Stephanie,
Quick Shine Deep Cleaner is safe to use on any sealed hard surface flooring and can only remove acrylic finishes like our Finish. We recommend testing a small area first to check for satisfactory results. For application/removal tips please contact customer service at 800-255-1891. We are always happy to help.
will it remove paint on a painted floor surface?
Quick Shine Deep Cleaner will remove acrylic based finishes so it could potentially remove some of the paint on the floor. We recommend testing a small area first.
Will quick shine cleaner damage the floor? Will it return to its original look?
Hi Lily,
No, Quick Shine Deep Cleaner is a safe way to remove our Finish from any hard surface flooring without removing factory or polyurethane finishes. Please contact customer service for application tips at 800-255-1891. We are always happy to help!
I applied Quick Shine Finish on my unsealed wood-look tile but slowly it seems like the color of the tile is coming off. I was told by the manufacturer of the wood-like tile to remove the Quick Shine Finish from the tiles. How can I remove the solution that is already in the tiles without affecting the wood-like design of the tiles?
Hi Josephine,
You can remove Quick Shine Finish with Quick Shine Deep Cleaner. Simply dilute our Deep Cleaner with hot water and apply to small sections at a time. Allow solution to sit for 3-4 minutes and mop or wipe away. You may have to repeat the process and leave the solution on a little longer if your tiles are porous. Quick Shine Deep Cleaner is only available online at this time at http://www.quickshine.net or http://www.walmart.com. For more information, please contact customer service at 800-255-1891. We are always happy to help!
Hi,
The previous owners always used quick shine on our hardwood floors, so there is likely a buildup. To protect the floors while moving in, I applied the stick-on floor protection film sold by Lowe’s and upon removal, it appears that the quick shine pulled off? I have large areas of dull floor where there is a distinct edge where the stick-on floor film stopped. I tried buffing and applying more quick shine to these areas and it its helping, but not completely fixing my problem. I do not think that the stick on film harmed the polyurethane on the floors. What do you recommend to restore my floors appearance in this situation??
Hi Matt,
The tape did not affect your original finish but most likely our Finish. Our Quick Shine Deep Cleaner can be used to spot treat the affected areas. Simply dilute our Deep Cleaner with hot water and apply to the area. Allow solution to sit for 3-4 minutes and mop or wipe away. Quick Shine Deep Cleaner is only available online at this time at http://www.quickshine.net or http://www.walmart.com. For more information, please contact customer service at 800-255-1891. We are always happy to help!
I clean houses and someone I work for bought a house with Laminate flooring and the previous owner applied quick shine floor finish over dirt and dog hair will the derp cleaner work on laminate
Hi Sandy,
Yes, Quick Shine Deep Cleaner will safely remove our Finish from your laminate floors. You can also spot treat any affected areas where there is pet hair.
Can I use quick shine to remove your finish from my luxury vinyl plank flooring?
Hi Sara,
Yes, we recommend removing our finish from Luxury Vinyl with Quick Shine Deep Cleaner. Simply dilute our Deep Cleaner with hot water and apply to 5′ sections at a time. Allow solution to sit for 3-4 minutes and mop away. Quick Shine Deep Cleaner is only available online at this time at http://www.quickshine.net or http://www.walmart.com. For more information, please contact customer service at 800-255-1891. We are always happy to help!
Question to all… I use quickshine polish on my hardwood floors and I have been pleased with it over the years. Anyone have a suggestion as to which type of pad I could purchase to help put a more even shine on with?? I simply have been using a swiffer dry pad and I don’t think I am getting maximum result with it. thanks
Hi Michael,
Great question! We recommend applying Quick Shine with our Hardwood Floor Mop Refill Pad. These pads can fit a standard Swiffer mop or you can purchase our Hardwood Floor Mop Kit which includes one pad. Here is a direct link to both items: https://quickshinefloors.com/product-categories/floor-care-tools/
I have spots where the QuickShine Luster has white spots. Somehow as I applied I agitated it and the wax lumped up. But its not everywhere. Can I use the Deep Clean to spot clean the wax and reapply Luster or do I need to remove from the entire floor and then reapply?
Hi Christine,
Yes, you can just spot treat the affected area. Simply dilute our Deep Cleaner with hot water and apply to area. Allow solution to sit for 3-4 minutes and mop or wipe away. Quick Shine Deep Cleaner is only available online at this time at http://www.quickshine.net or http://www.walmart.com. For more information, please contact customer service at 800-255-1891. We are always happy to help!
I used quick shine on my older vinyl kitchen floor. Looked amazing for a few days. With kids and dogs things got spilled or dribbled. Augh! It makes a mark and you cannot get rid of it. Now I’m desperately trying to get the quick shine product off floor. I will never use this product again.
Hi Colleen,
Please reach out to customer service at 800-255-1891 and we can further assist. It appears our finish had not fully cured when moisture was hitting the surface of the floor and it absorbed. Our Quick Shine Deep Cleaner will safely remove our Finish and take you back down to the original floor surface.
don’t use this product its like painting with varathane horrible to try and remove!!!!
Hi Rick,
Quick Shine is designed to last on floors until you are ready to remove it. Simply dilute our Deep Cleaner with hot water and apply to 5′ sections at a time. Allow solution to sit for 3-4 minutes and mop away. Quick Shine Deep Cleaner is only available online at this time at http://www.quickshine.net or http://www.walmart.com. For more information, please contact customer service at 800-255-1891. We are always happy to help!